How To Backwash A Sand Pool Filter



If you have a swimming pool with a sand filter then quite frequently you will need to backwash the filter to remove the dirt and other debris that gets trapped in it. For correct dosage follow the instructions on the bottle.


How To Backwash A Sand Filter Pool University Pool Filters Pool Filter Sand Pool Sand

Turn on the pump and backwash the filter for 3-5 minutes Turn off the pump and move the valve back to the Filter position Open the pump lid and pour the sand filter cleaner into the pumps strainer basket.

How to backwash a sand pool filter. If it increases by 10 psi you need to backwash the filter again. Switch the filter valve to the. Now you know how to replace a lateral in a pool sand filter and you didnt even have to call for help.

Make a note of your pressure gauge reading because it marks the clean sand filter pressure for your system. Completely turning off the pump will prevent any new water from entering the filter while you are working on it. After the hose fills with water backwash your sand filter for 2 - 3 minutes or until water runs clear.

Next turn off the pool heater if applicable and wait approximately 15-20 minutes for the water to cool down. Twist and unlock the plunger T-handle then pull and twist the plunger upward 2 - 3 inches. Add DE powder to the filter to replace the amount that was backwashed out.

The powder will travel through the plumbing and effectively recharge the filter. Switch the Setting on the Valve. When backwashing and performing other functions using the multi port valve on these pools are you supposed to set all sand filters to backwash and turn on the pump one at a time or something completely different.

Turn the pump on and backwash for 2 minutes or until the water in the sight glass located on the filter is running clear. Turn Off the Pump. Run the pump for 2 or 3 minutes to clean the sand in the filter.

Switch on the pump. Change the setting on your pool filter valve. Attach the Backwash Hose.

How to Backwash a Pool Filter. Backwashing a pool is a simple straightforward process that involves switching the multiport valve setting of the pool sand filter to Backwash then running the pump for a few minutes. Turn the power off to stop the rinse process.

Switch off the pump motor at the power supply. When the water inside the monitor sight glass turn to sparkle clear turn off the filter. Turn off the pool pump.

Once the pump has been turned off and the circuit breaker switched off you are free to change the setting on the filter. Open the air bleeder assembly on your filter and turn pump on. Turn the Pump Back On.

Allow the pump to rinse the filter for 1 to 2 minutes. Steps to Backwash a DE or Sand Filter System. If the Multiport valve is in either the Filter Recirculate or Backwash position all the debris that is being sucked up from the bottom of the swimming pool will be passing through the sand filter and back into the pool.

Watch the pressure gauge for spikes. How to Backwash a Pool Sand Filter. Backwash the filter 2 to 3 minutes to strip old DE powder contaminants debris and small particles from the filters grids.

Check the skimmer opening and make sure that the water in the pool is at least halfway up the opening. You can also observe monitor sight glass to see the water. The sand filter will quickly get clogged and the smaller debris particles will be pumped straight back via the return jets.

Turn Off the Pump. Turn off the pump. Uncover the skimmer closest to the pump and filter and slowly pour the needed amount into the skimmer while the system is running.

Turn the multiport filter valve to the backwash setting. Set the filter valve handle to the Backwash position and ensure the handle locks in place. This video will show you how to use the different settings to backwash and clean your above ground pool sand filterIn The Swim Pool Product Offer.

If not add more water to the pool. Turn the power back on to start the rinse process. Hey all This may be a simple answer but Ive noticed plenty of larger pools have multiple sand filters - anywhere from 2 to 8.

Depress the multiport filter valve handle move it from the RINSE position to the FILTER position lock it there.


How To Use A Multiport Valve On A Pool Filter Swimming Pool Filters Pool Sand Pool Filters


Pin On Tutorials


Pool Sand Filter Maintenance Backwash Pool Filter Pool Filter Sand Swimming Swimming Pool Construction Diy Swimming Pool Swimming Pool Plumbing


Waterco Micron Eco S602 24 Sand Filter W 50mm Valve Diy Swimming Pool Swimming Pool House Swimming Pool Equipment


How To Backwash And Clean Above Ground Sand Pool Filter Sand Filter Pool Bath Swimming Swim Please R Pool Sand Pool Filters Swimming Pool Maintenance


How To Use Different Pool Filter Valve Settings Youtube Pool Pump Pool Filters Splash Pool


How To Backwash A Sand Filter Pool Sand Pool Filters In Ground Pools


How To Backwash Intex Sand Filter Above Ground Pool Pumps Pool Pump Water Trough Pool


How To Backwash A Sand Filter Sand Filter For Pool Pool Filters Pool Care


Backwashing Best Practices Intheswim Pool Blog Intheswim Pool Blog Swimming Pool Heaters Pool Plumbing Pool Filters


How Does A Pool Sand Filter Work Hunker Pool Sand Pool Pumps And Filters Pool Filter Sand


Pin On Blog Research


How To Clean Your Sand Pool Filter Diy Pool Filters Pool Filter Sand Swimming Pool Maintenance


How To Change Pool Filter Sand Pool Accessories Cool Pools Pool Supplies


How To Backwash A Pool Filter Pool Filters Pool Filter Sand Swimming Pool Filters


Hayward De Pool Filter Cutaway Pool Pool Hacks Pool Filters


How To Clean Your Sand Pool Filter Diy Cleaning Pool Filters Pool Filters Pool Plumbing


Pet Pool Warehouse Knysna Summer Pool Tip Filter Sand How Old Is Your Filter Sand Filter Sand Pool Filter Sand Swimming Pool Construction Pool Water Features


Visual Explanation Of A Sand Filter In Backwash Position Swimming Pools Pool Equipment Pool Patio